Description
SC/APC LC/APC 100m Patch Cord – Single-Mode Fiber for FTTH
The Patchcord SC/APC LC/APC 100m connects two compatible optical ports with different connector types. Specifically, it has SC/APC at one end and LC/APC at the other. It can therefore provide a continuous optical path between suitable ports without an additional intermediate cable.
According to the markings on the ARCTOS test report in the photo, the product features G652D 9/125 μm single-mode fiber, Simplex construction and a yellow jacket made of LSZH with a diameter of 1.8 mm. The 100-meter length also accommodates installations with longer optical paths.
Where Is the SC/APC LC/APC 100m Patch Cord Used?
Technicians choose this patch cord when the installation has an SC/APC port at one end and an LC/APC port at the other. However, they must confirm the fiber type, polish and port compatibility before connecting it.
For example, the cable can be used for the following applications, provided that the actual ports are suitable:
- Fiber optic connections in FTTH and FTTx projects.
- Optical distribution frames, ODFs and patch panels.
- Connection to compatible telecommunications equipment.
- Single-mode optical paths in laboratory and technical setups.
- Testing with instruments equipped with suitable ports or adapters.
SC/APC at One End and LC/APC at the Other
SC and LC describe different mechanical connector types. APC, on the other hand, refers to the angled polish of the fiber end face. On this cable, both ends are APC, according to the test report.
Connect SC/APC to a suitable SC/APC port and LC/APC to a suitable LC/APC port. Do not mate APC with UPC, as the difference in polish may cause signal loss or damage.
For more information, read the LC vs SC Connector comparison and the guide SC/APC vs SC/UPC from ARCTOS.
Single Mode G652D 9/125 μm
The report accompanying the photographed product specifies Single Mode G652D 9/125 μm. This is a category of single-mode fiber for telecommunications networks. Technicians should therefore select a compatible single-mode optical path and matching equipment.
The official ITU-T G.652 recommendation describes the general properties of this family of optical fibers. However, the recommendation does not itself certify this specific patch cord or verify its measurements.
Simplex Construction and 1.8 mm LSZH Jacket
The Simplex construction means that the patch cord contains one optical fiber. The outer diameter of 1.8 mm allows a relatively slim cable to be managed along suitable routes.
The marking LSZH describes the jacket type (Low Smoke Zero Halogen). However, only the corresponding manufacturer documents can establish a specific reaction-to-fire class or CPR compliance.
100-Meter Length for a Continuous Optical Path
With a length of 100 m, technicians can cover the route between two compatible points without an additional intermediate patch cord. Installers can therefore organize the cabling according to the project requirements.
Before installation, calculate the required length and allowance. Protect the fiber from sharp bends and mechanical stress. We do not have a technical document specifying a minimum bend radius for this product.
SC/APC LC/APC 100m Patch Cord Specifications
| Specification | Value |
|---|---|
| Product type | Fiber optic patch cord |
| Length | 100 m |
| Connector A | SC/APC |
| Connector B | LC/APC |
| Fiber Type | Single Mode (SM) |
| Fiber marking | G652D |
| Nominal fiber dimensions | 9/125 μm |
| Construction | Simplex |
| Jacket | LSZH |
| Outer Diameter | 1.8 mm |
| Cable Color | Yellow |
| Connector color in the photo | Green |
The specifications are based on the photo and the markings on the ARCTOS test report. However, we have not identified a separate official datasheet from the original manufacturer.
Practical Benefits for Technicians
- Different SC/APC and LC/APC connectors: enable connection between two suitable optical port types.
- 100 m length: provides a continuous optical path where distances and installation requirements call for it.
- Single Mode G652D: matches the fiber type required by corresponding single-mode networks.
- Simplex: provides one independent optical path.
- 1.8 mm diameter: makes cable management along suitable routes easier.
- Yellow cable: helps visually identify the optical path.
Correct Selection, Compatibility and Package Contents
First, check the port and polish at each end of the equipment. In particular, an LC/UPC port is not a substitute for an LC/APC port. Then confirm the required single-mode fiber and installation length.
The photo shows a cable with two connectors and protective caps. We do not have an official packing list documenting additional accessories or accompanying documents.
If your installation requires SC/APC–LC/UPC instead of LC/APC, see the separate SC/APC–LC/UPC 100m Patch Cord. For two SC/APC ports, see the Patchcord SC/APC–SC/APC 100m.
Frequently Asked Questions about the SC/APC–LC/APC Patch Cord
1. Which connectors does the patch cord have?
One end has an SC/APC connector and the other has an LC/APC connector. This configuration therefore differs from SC/APC–LC/UPC and SC/APC–SC/APC cables.
2. Is it suitable for FTTH installations?
Yes, provided that the FTTH or FTTx path uses compatible single-mode fiber and requires SC/APC at one end and LC/APC at the other. However, technicians must verify the actual equipment ports.
3. Can I connect LC/APC to an LC/UPC port?
No. APC and UPC connectors have different end-face polishes. Do not mate them directly. This end therefore requires a matching LC/APC port.
4. What does G652D 9/125 μm mean?
G652D identifies a category of single-mode fiber, while 9/125 μm is the nominal commercial designation of its dimensions. For more information, consult the ITU-T G.652 recommendation.
5. What does an LSZH jacket mean?
LSZH stands for Low Smoke Zero Halogen. However, specific reaction-to-fire certification or a CPR class requires the corresponding technical documents.
6. Does the patch cord come with guaranteed loss results?
The photo includes a report with specific measured values. However, we do not have technical documentation defining these values as guaranteed limits for every item.
Patch Cord Selection and Contacting ARCTOS
Before ordering, make sure that SC/APC and LC/APC ports match the actual needs of your installation. Also check the fiber type, required length and routing conditions.
For help choosing a suitable patch cord, contact ARCTOS Solutions.
Official Technical Reference for G.652 Fiber
For general information about the G.652 category, refer to the official ITU-T G.652 recommendation. The recommendation does not certify this specific cable.









